大阳城集团娱乐游戏

I Summary For Slag Slurry Pump

Slag Slurry Pump

As a single-stage-single-suction horizontal cantilever-type centrifugal one, model ZM slag slurry pump is designed through absorbing advantages of similar products from home and aboard. It is convenient to install and easy to disassemble and repair. ZM slag slurry pump head part: ENINE ZM slag slurry pump has double pump casings in structure. That is to say, it is made up of front pump casing, back pump casing, front guar plate, back guard plate, sheathing, shaft casing. The flow contact parts are made of JM3 materials, while the front and back pump casings are made of gray cast-iron or nodular cast iron, The outlets of the pump can be installed at the interval of 45℃,at eight angles, according to users requirements. At the front and back cover plates there are back blades to lower leakage, so as to extend the life and increase efficiency of the pump. The shaft seal part: The shaft seal has two forms: shaft seal of auxiliary blade wheel and filling seal. The shaft seal of auxiliary blade wheel is featured with not thinning ore slurry, long life of seal and good effect of seal, etc. The filling seal has simple structure and is convenient to repair. Drive part: Model ZM(slag) slurry pump can be directly driven. The bearing support, in combination with bearing body, has high strength in structure, big diameter of pump shaft, good flexibility, and short cantilever. Even if in bad working condition, no bending and vibration can arise. Because of using heavy single-line cone roller bearing, it can stand axial and radial loads of the pump. The shaft is lubricated with oil. At both ends of the bearing body there are bearing covers, inside of which there is seal ring. The ring can effectively protect ore slurry from penetration and the lubricating oil from leaking. This can make sure that the bearing can run safely. In accordance with users requirements, the drive part of the bearing can be in double-open type, and lubricated with thin oil. This can lower the temperature of the shaft.

II Property Parameters Table For Slag Slurry Pump

model	head	capacity Q		Speed	Motor power	Permissible suctioned height	Efficiency h %
model	head	M³/h	L/S	Speed	Motor power	Permissible suctioned height	Efficiency h %
100ZM-25	23-30	150-500	14.6-55.5	1450	45	5.5	65-67
100ZM25A	25-35	200-250	55.5-69.4	1450	55	5.5	65-67
100ZM-40	35-45	180-200	50-55.5	1450	55	5.5	43-48
100ZM-40A	40-50	200-250	55.5-69.4	1450	75	5.5	70-75
100ZM-45	40-50	150-180	41.6-50	1450	55	5	50-60
100ZM-70	65-75	200-250	55.5-69.4	1450	110	5.5	55-60
100ZM-90	80-90	120-180	33.3-50	1450	110	5.5	50-55
150ZM-32	32-36	300-320	83.3-89	980	75	5	70-73
150ZM-32A	32-36	420-450	116.6-125	980	90	5	70-73
150ZM-50	50-60	250-320	69.34-89	980	90	5	67-70
150ZM-50A	50-60	400-450	111.1-125	980	132	5	67-70
150ZM-80	90-75	250-300	69.4-89	980	132	5	60-61
150ZM-100	95-105	400-450	116.6-125	980	250	5	60-64
200ZM-45	40-50	480-550	133.3-152.7	980	132	5.5	70-75
200ZM-45A	40-50	680-750	1858.9-208.3	980	185	5.5	75-78
200ZM-75	70-80	450-550	125-153.7	980	250	5.5	70-75
200ZM-75A	70-80	650-750	180.5-208.3	980	300	5.5	70-75
200ZM-95	90-100	480-580	133.3-161.1	980	320	5.5	55-58
200ZM-50	50-60	650-700	180.5-194	980	185	5.5	76-80
250ZM-50A	50-60	950-1000	263.9-277.7	980	260	5.5	75-80
250ZM-85	80-90	630-700	175-194.4	980	320	5.5	70-72
250ZM-85A	80-90	930-1000	258.3-277.7	980	450	5.5	70-73
250ZM-100	90-100	1000-1200	277.7-333.3	980	560	5.5	60-65
300ZM-40	40-50	1100-1200	305.5-333.3	730	270	4	75-80
300ZM-60	60-67	1500-1600	416.7-444.4	730	480	4.5	75-80

Slag Slurry Pump Related Products

Next:Stainless Steel Chemical Centrifugal Pump

Catalog:大阳城集团娱乐游戏Chemical Pumps

Above:大阳城集团娱乐游戏Single-Stage Single Suction Centrifugal Pump